Automation Lab
Department of Mechanical Engineering
Indian Institute of Technology Delhi

International Journal papers

  1. Jha Sunil and V. K. Jain (2004), "Design and Development of Magnetorheological Abrasive Flow Finishing (MRAFF) Process" International Journal of Machine Tools & Manufacture. Vol. 44, no. 10, pp. 1019-1029.

  2. Jha Sunil, V. K. Jain and Ranga Komanduri, "Effect of Extrusion Pressure and Number of Finishing Cycles on Surface Roughness in Magnetorheological Abrasive Flow Finishing (MRAFF) Process", International Journal of Advanced Manufacturing Technology 33 (7-8), pp. 725-729.

  3. Jha Sunil and V. K. Jain, "Modeling and Simulation of Surface Roughness in Magnetorheological Abrasive Flow finishing (MRAFF) Process", Wear Vol. 261, Issues 7-8, 20 October 2006, Pages 856-866.

  4. Jha Sunil and V. K. Jain, "Parametric Analysis of Magnetorheological Abrasive Flow Finishing (MRAFF) Process", International Journal of Manufacturing Technology and Management, special issue on Microfabrication 2008 - Vol. 13, No.2/3/4 pp. 308 " 323.

  5. Jha Sunil and V. K. Jain (2006), "Nanofinishing of Silicon Nitride (Si3N4) Workpieces using Magnetorheological Abrasive Flow Finishing", International Journal of Nanomanufacturing, Vol. 1, No. 1, pp. 17-25.

  6. N. K. Jain, V. K. Jain, Jha Sunil, "Parametric optimization of advanced fine finishing processes", International Journal of Advanced Manufacturing Technology (2007) 34:1191"1213.

  7. Jha Sunil, Manoj Modi, Modeling and analysis of powder mixed EDM process, Int. J. Mechanical Engineering, Vol. 2, Issue 2, Jul-Dec 2009.

  8. Jha Sunil, V. K. Jain, Rheological characterization of magnetorheological polishing fluid for MRAFF, International Journal of Advanced Manufacturing Technology (2009) 42:656"668.

  9. Jha Sunil, V. K. Jain, A novel nanofinishing process using magnetorheological abrasive polishing fluid, Int. J. Manufacturing Technology and Management, Vol. 21, Nos. 1/2, 2010.

  10. Anant K Singh, Jha Sunil, P. M. Pandey, Design and Development of Nanofinishing Process for 3D Surfaces Using Ball End MR Finishing Tool, Int. J. of Machine Tools and Manufacture, Volume 51, Issue 2, February 2011, Pages 142-151.

  11. Anant K Singh, Jha Sunil, P. M. Pandey, Nanofinishing process for 3D freeform surfaces using ball end MR finishing tool, Int. J. of Materials and Manufacturing Processes (accepted 2010).

  12. Jha Sunil; Jain, VK, (2006); Nanofinishing techniques, Micromanufacturing and nanotechnology, 171-195.

  13. Jha Sunil; Jain, Vijay Kumar(2008); "Parametric analysis of magnetorheological abrasive flow finishing process International Journal of Manufacturing Technology and Management" Volume 13, 02-Apr ,Pages 308-323.

  14. Singh, Anant Kumar; Jha Sunil; Pandey Pulak M (2013); "Mechanism of material removal in ball end magnetorheological finishing process" Wear,302,number 1, Pages 1180-1191.

  15. Singh, Anant Kumar; Jha Sunil, Pandey Pulak Mohan; (2012); "Parametric analysis of an improved ball end magnetorheological finishing process" Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture.

  16. Niranjan, Mahendra Singh; Jha, Sunil (2014); "Flow behaviour of bidisperse MR polishing fluid and ball end MR finishing", Procedia Materials Science, Volume 6 Pages 798-804.

  17. Singh Anant Kumar; Jha Sunil Pandey Pulak M (2012); "Performance evaluation of improved ball end magnetorheological finishing process" World Academy of Science and Technology, Volume 6, Page No 1193-97.

  18. Niranjan Mahendra, Jha Sunil, Kotnala RK (2014); Ball end magnetorheological finishing using bidisperse magnetorheological polishing fluid, Materials and Manufacturing Processes Volume 29 No.4 Pages 487-492.

  19. Singh Anant Kumar; Jha Sunil; Pandey Pulak M; (2011) "Improved ball end magnetorheological finishing process" Proceedings of the ASME.

  20. Rajput Mridul S; Pandey Pulak M, Jha Sunil (2013); "Experimental investigations into ultrasonic-assisted jet electrodeposition process" Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, volume 954405413506198.

  21. Jha Sunil, Jain V K, Choudhury SK (2004); "On the performance of Abrasive flow finishing process" Proceedings of Precision Engineering, 216-223.

  22. Singh Anant Kumar, Jha Sunil; Pandey PM (2010);"Nanofinishing Process for 3D Freeform Surfaces Using Ball End MR Finishing Tool", Proceedings of the 36th International MATADOR Conference Page No.67-70.

  23. Rajput Mridul S; Pandey, Pulak M, Jha Sunil (2015); "Micromanufacturing by selective jet electrodeposition process" The International Journal of Advanced Manufacturing Technology volume 7642461, pages 61-67.

  24. Singh Anant Kumar, Jha Sunil, Pandey Pulak M (2014); "A Novel Ball End Magnetorheological Finishing Process" ASME 2014 International Mechanical Engineering Congress and Exposition, Pages V02BT02A032-V02BT02A032.

  25. Jha Sunil, Jain V K (2005); "Evaluation of Rheological Properties of Magnetorheological Polishing Fluid and Their Effect on Surface Finish in Ultra Precision Finishing Processes" World Tribology Congress III, pages 843-844.

  26. Saraswathamma K, Jha Sunil; Rao PV(2015); "Experimental investigation into Ball end Magnetorheological Finishing of silicon" Precision Engineering, Volume 42, Pages 218-223.

  27. Nair R Sandeep, Singh, Trilok Ramkumar J, Jha Sunil, (2011);"Development and experimental investigation of MAF setup for finishing of ultra high speed shafts" International Journal of Abrasive Technology, Volume 44, Pages 325-345.

  28. Niranjan Mahendra Singh, Jha Sunil (2015);"Experimental investigation into tool aging effect in ball end magnetorheological finishing" The International Journal of Advanced Manufacturing Technology, Volume 8042713, Pages1895-1902.

  29. Alam, Zafar; Iqbal Faiz, Jha Sunil (2015); "Automated control of three axis CNC ball end magneto-rheological finishing machine using PLC" International Journal of Automation and Control Volume 93,Pages 201-210.

  30. Singh Anant Kumar; Jha Sunil, Pandey Pulak M (2015); "Performance Analysis of Ball End Magnetorheological Finishing Process with MR Polishing Fluid" Materials and Manufacturing Processes, Volume 30 No.12, pages1482-1489.

  31. Rajput Mridul Singh, Pandey Pulak Mohan,Jha Sunil (2015); "Modelling of high speed selective jet electrodeposition process" Journal of Manufacturing Processes Volume 17, Pages 98-107.

  32. Singh Anant Kumar; Jha Sunil, Pandey Pulak M (2013); "Rheological Behavior Of MR Polishing Fluid In Ball End Magnetorheological Finishing Process". Magnetohydrodynamics (0024-998X),Volume 49.

  33. Saraswathamma, K, Jha Sunil, Rao P Venkateswara (2015); "Rheological Characterization of MR Polishing Fluid Used for Silicon Polishing in BEMRF Process" Materials and Manufacturing Processes, Volume 30, No. 5 ,Pages 661-668.

  34. Jha Sunil, Jain, Vijay Kumar; (2010) "A novel Nanofinishing process using magnetorheological abrasive polishing fluid" International Journal of Manufacturing Technology and Management, Volume No. 21.

  35. Rajput Mridul S, Pandey Pulak M, Jha Sunil (2014); "Fabrication of nano-sized grain micro features using ultrasonic-assisted jet electrodeposition with pulsed current supply" Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Volume 954405413520142.

  36. K, Saraswathamma, Jha Sunil, Rao P.V. (2015); "Design of Parallel Plate Magnetorheometer for evaluating properties of Magnetorheological polishing fluid", Materials Today Proceedings, Volume 24, Pages3251-3259.

  37. Niranjan Mahendra Singh; Jha Sunil (2015); "Optimum selection of machining parameters in ball end magnetorheological finishing process" International Journal of Precision Technology Volume 542463 Pages 217-228).

  38. Iqbal, Faiz, Jha Sunil; "Automatic Control of Ball End Magneto-Rheological Finishing" MANFEX 201.

International Conference Papers

  1. Jha Sunil, "Magnetorheological Abrasive Flow Finishing process Optimization using Genetic Algorithm", 2nd International All India Manufacturing Technology, Design and Research (AIMTDR 2008) Conference, IIT Madras, Chennai.

  2. Sandeep Nair R., Karthikeyan G., Ramkumar J., Jha Sunil, and Anil Varghese, "Development of MAF setup for finishing of Ultra high speed shafts", 2nd International All India Manufacturing Technology, Design and Research (AIMTDR 2008) Conference, IIT Madras, Chennai.

  3. A. K. Singh, Jha Sunil, P. M. Pandey, "Nanofinishing process for 3D freeform surfaces using ball end MR finishing tool, MATADOR 2010", July 14-16, 2010, Manchester University, UK.

  4. A. K. Singh, Jha Sunil, P. M. Pandey, "A process of generating magnetically controlled ball end smart abrasive laden shape for nanofinishing of 3D intricate shaped surfaces" 2nd International Conference on Production and Industrial Engineering CPIE-2010, NIT Jalandhar.

Designed by Navdeep Singh